# https://tscircuit.com/rushabhcodes/ESP32 Channel: #designreview Source: https://discord.com/channels/1233487248129921135/1554098466249248880 Started: 2026-09-28T12:59:48.407000+00:00 Last activity: 2026-10-01T22:10:48.542000+00:00 ## ! Rushabh | Linux Shill — 2026-09-28T11:52:28.107000+00:00 https://tscircuit.com/rushabhcodes/ESP32-E-Reader#files Ready for second review <@&1420812538421051555> ## ! Rushabh | Linux Shill — 2026-09-28T12:59:50.341000+00:00 .. ## ! Rushabh | Linux Shill — 2026-09-28T13:00:01.502000+00:00 <@809856037376491570> <@778624824875941908> ## Rishabh — 2026-09-29T10:49:24.038000+00:00 Where are the schematic text's? That was the first thing we should add before requesting review as mentioned yesterday ## Rishabh — 2026-09-29T10:49:46.059000+00:00 Also use multisheet ## ! Rushabh | Linux Shill — 2026-09-29T17:26:39.436000+00:00 <@398467566588264449> ## Abse — 2026-09-29T17:27:24.576000+00:00 U1’s battery output also feeds the regulator and system. Running the reader while charging can interfere with charge termination; USB-only operation without a battery is also not assured. | Add a power-path/load-sharing circuit, or explicitly require charging with the reader switched off. P1 grounds GPIO9, but GPIO8 is used for SPI clock with no explicit pull-up. Reliable ROM download mode requires GPIO8 high when GPIO9 is low. | Add a suitable GPIO8 pull-up and verify programming with the display and SD card connected. | A 3.3 V LDO cannot maintain 3.3 V throughout a single-cell LiPo’s discharge range. | Verify the lowest usable battery voltage under Wi-Fi, SD-card and display loads; consider a buck-boost supply. | ## Rishabh — 2026-09-30T16:35:44.284000+00:00 https://www.xteink.com/products/xteink-x3 Quite small and also has a magsafe <@757706909351411845> <@452450065941004289> ## Rishabh — 2026-09-30T16:36:14.972000+00:00 [attachment] Attachment: image.png — https://community.tscircuit.com/media/1554894656565813360 ## Seve — 2026-09-30T18:22:18.469000+00:00 <@452450065941004289> yep that's the one, literally perfect ## ! Rushabh | Linux Shill — 2026-09-30T18:22:30.987000+00:00 yeah ## ! Rushabh | Linux Shill — 2026-10-01T22:04:29.942000+00:00 The hot-swappable buttons make the board too wide to fit behind a phone, and the display i selected before this discussion is also a bit too large. Is it okay to make the first prototype bigger and work toward a phone-sized version later, or should we switch to smaller buttons and display now? ## ! Rushabh | Linux Shill — 2026-10-01T22:06:38.106000+00:00 [attachment] Attachment: K7DmJuEYAAAAASUVORK5CYII.png — https://community.tscircuit.com/media/1555340188887027793 ## ! Rushabh | Linux Shill — 2026-10-01T22:07:31.213000+00:00 the ref that rishabh shared also uses side buttons ## ! Rushabh | Linux Shill — 2026-10-01T22:07:47.450000+00:00 <@757706909351411845> ## ! Rushabh | Linux Shill — 2026-10-01T22:10:48.542000+00:00 I think we should switch to smaller standard buttons. That would reduce the board’s width and bring us closer to a phone-sized design.