# Thread

Channel: #designreview
Source: https://discord.com/channels/1233487248129921135/1542277677145264139
Started: 2026-08-26T21:05:48.366000+00:00
Last activity: 2026-08-26T22:46:21.499000+00:00

## Anas — 2026-08-26T21:00:52.365000+00:00

[attachment]
Attachment: MgsAAAAAAAAQEAIAAAAAAAAAAAAAAACAgBAAAAAAAAAAAAAAAAAAEBACAAAAAAAAAAAAAAAAAAJCAAAAAAAAAAAAAAAAAEBACAAAAAAAAAAAAAAAAAAICAEAAAAAAAAAAAAAAAAAASEAAAAAAAAAAAAAAAAACAgBAAAAAAAAAAAAAAAAAAEhAAAAAAAAAAAAAAAAACAgBAAAAAAAAAAAAAAAAAAEhAAAAAAAAAAAAAAAAACAgBAAAAAAAAAAAAAAAAAABIQAAAAAAAAAAAAAAAAAgIAQAAAAAAAAAAAAAAAAABAQAgAAAAAAAAAAAAAAAAACQgAAAAAAAAAAAAAAAABAQAgAAAAAAAAAAAAAAAAACAgBAAAAAAAAAAAAAAAAQEAIAAAAAAAAAAAAAAAAAAgIAQAAAAAAAAAAAAAAAIBt8gcCup4yVgZCrwAAAABJRU5ErkJggg.png — https://community.tscircuit.com/media/1542277676650467358

## Seve — 2026-08-26T21:05:48.996000+00:00

this channel is for physical board designs, this is more appropriate for <#1265314333764878387> for now, you should use schematic sections not boxes

## Seve — 2026-08-26T21:06:11.081000+00:00

otherwise it's pretty good

## Seve — 2026-08-26T21:06:31.382000+00:00

it'll probably be even better once all the schematic-trace-solver changes are live

## Seve — 2026-08-26T21:07:00.429000+00:00

these should be test points
Attachment: CleanShot_2026-08-26_at_14.06.492x.png — https://community.tscircuit.com/media/1542279220695400488

## Seve — 2026-08-26T21:07:17.210000+00:00

likewise
Attachment: CleanShot_2026-08-26_at_14.07.092x.png — https://community.tscircuit.com/media/1542279290878697635

## Seve — 2026-08-26T21:07:52.755000+00:00

this chip doesn't match
Attachment: CleanShot_2026-08-26_at_14.07.402x.png — https://community.tscircuit.com/media/1542279440170618911

## Seve — 2026-08-26T21:08:04.675000+00:00

[attachment]
Attachment: CleanShot_2026-08-26_at_14.07.572x.png — https://community.tscircuit.com/media/1542279490279972934

## Anas — 2026-08-26T21:08:22.312000+00:00

also here is issue I think for resistance value text
Attachment: Screenshot_2026-08-26_at_11.07.41_PM.png — https://community.tscircuit.com/media/1542279564120694894

## Seve — 2026-08-26T21:08:57.673000+00:00

yea i think this happens if you set schSize to a number

## Seve — 2026-08-26T21:09:05.940000+00:00

i was tell <@436098556974333952> that that messes things up

## Anas — 2026-08-26T22:11:24.458000+00:00

[attachment]
Attachment: wNzDtTbf468ygAAAABJRU5ErkJggg.png — https://community.tscircuit.com/media/1542295427456438342

## Seve — 2026-08-26T22:11:49.317000+00:00

well make sure to have a <schematicsheet />

## Seve — 2026-08-26T22:11:51.739000+00:00

it might not fit

## Seve — 2026-08-26T22:12:01.973000+00:00

see in the bottom right how it says "Size: B"

## Seve — 2026-08-26T22:12:22.836000+00:00

that's a "large" sheet, ANSI_B, <@436098556974333952> is trying to add support for that but it's not supported yet

## Anas — 2026-08-26T22:39:06.155000+00:00

did u support that? Is it ready?
Attachment: Rp0hTR4obncAAAAASUVORK5CYII.png — https://community.tscircuit.com/media/1542302397077004348

## Seve — 2026-08-26T22:44:06.793000+00:00

he's afk i don't think he has support for it yet

## Seve — 2026-08-26T22:44:16.332000+00:00

<@436098556974333952> can you see discord mentions?

## Seve — 2026-08-26T22:44:55.711000+00:00

fwiw tho

## Seve — 2026-08-26T22:44:59.030000+00:00

your schematic is too big

## Seve — 2026-08-26T22:45:06.034000+00:00

i think you could make it smaller

## Seve — 2026-08-26T22:45:20.227000+00:00

i THINK you have a lot of extra spacing

## Seve — 2026-08-26T22:45:52.392000+00:00

you can probably fit it in size A and the pdf will probably look better if you do

## Enix — 2026-08-26T22:46:21.499000+00:00

yeah in a draft pr, will check the code and set it up for review