# Seve - very easy schematic trace solver fix

Channel: #contributor
Source: https://discord.com/channels/1233487248129921135/1532100076590338211
Started: 2026-07-29T18:58:43.835000+00:00
Last activity: 2026-07-31T17:36:58.585000+00:00

## Seve — 2026-07-29T18:58:43.302000+00:00

very easy schematic trace solver fix
Attachment: image.png — https://community.tscircuit.com/media/1532100076346806392

## mohan-bee — 2026-07-30T13:13:23.163000+00:00

<@757706909351411845>  

can you tell me which one looks better.. by redability ??
Attachment: image.png — https://community.tscircuit.com/media/1532375557679874229

## mohan-bee — 2026-07-30T13:13:32.307000+00:00

or this ?
Attachment: image.png — https://community.tscircuit.com/media/1532375595986583562

## mohan-bee — 2026-07-30T13:13:53.838000+00:00

i feel like the second is better .

## Seve — 2026-07-30T16:43:53.019000+00:00

yea second is better

## Vanuan — 2026-07-31T17:23:28.466000+00:00

It depends on the role of that capacitor. Here it seems it's the decoupling. I'd say neither. First of all it should be rotated, secondly it should be as close as possible to the pin it's serving. Topology suggests it's a bulk decap for VCC. Small capacitance and awkward placement near the pin says it's decap

## Vanuan — 2026-07-31T17:25:26.414000+00:00

This way better communicates the intent, although VCC could be further or more to the left, while the ground could be placed immediately after the cap
Attachment: Screenshot_20260731-182415.png — https://community.tscircuit.com/media/1532801376864833677

## mohan-bee — 2026-07-31T17:26:54.987000+00:00

i think that is now improved to be like this :
Attachment: group-match-adapt3-schematic.snap.png — https://community.tscircuit.com/media/1532801748325109790

## mohan-bee — 2026-07-31T17:27:02.371000+00:00

how is this now ? <@375462685728440330>

## Vanuan — 2026-07-31T17:27:57.549000+00:00

Routing is really good if this is not automatic placement

## Vanuan — 2026-07-31T17:29:18.503000+00:00

Though I would rotate the VCC anchor to be on the side

## Vanuan — 2026-07-31T17:30:36.600000+00:00

Or draw a global vcc wire on top and tap local wires from there

## Vanuan — 2026-07-31T17:32:08.569000+00:00

One could also separate grounds, but that's besides the point of autorouting

## mohan-bee — 2026-07-31T17:33:01.021000+00:00

are you saying like you don't prefer the GND to be routed ?

## Vanuan — 2026-07-31T17:33:41.121000+00:00

I guess it's an authoring and design intent issue.

## Vanuan — 2026-07-31T17:36:58.585000+00:00

Both  are valid choices
Attachment: images.jpg — https://community.tscircuit.com/media/1532804279885238455
Attachment: 4510-4511-Example-Circuit-1024x478_1.png — https://community.tscircuit.com/media/1532804280178835648